Moisture shrink

dry weight = wet × (100 − initial%) ÷ (100 − final%) − handling% × wet

Moisture is wet basis. Handling loss is a percentage of the initial (wet) weight, as in drying tables and Iowa State A2-32 (default 0.5%). A buyer's constant shrink factor is compared by subtracting the true water shrink from factor × points (Purdue NCH-61). Tests reproduce Purdue's 1,000 lb of 25% corn → 882.6 lb and its Table 2 values (0.83% and 1.46% for 1.25 and 1.30 factors on 28% corn).

Drying cost

Energy = wet bushels × points × factor: 0.02 gal LP (UMN, NDSU; Iowa State 0.018), 0.01 kWh (UMN, Iowa State), and 0.0184 per bu-point for natural gas (UMN). UMN states the natural-gas figure as "cubic feet"; by heat content it matches 0.02 gal of propane only as hundreds of cubic feet (ccf, about one therm), so the calculator uses ccf. Factors are scaled by bushel weight ÷ 56 for crops other than corn. Tests reproduce UMN's $0.205/bu (21→16%, $2 LP, $0.10 kWh) and NDSU's 24 gallons for 120 bu from 25% to 15%.

Sell wet vs. dry

Iowa State AgDM A2-32 method: wet sale at a percent-per-point price discount on wet bushels; elevator drying with a percent-per-point shrink factor and a per-point charge on wet bushels; on-farm drying with true water shrink, a handling loss and a per-point cost on wet bushels. Tests reproduce A2-32's $4,450, $4,351 and $4,377.50 (within ISU's rounding to 925 bushels).

Bin capacity

Cylinder π r² h plus or minus a cone π r² h ÷ 3 for the top, plus a cone for a hopper, times 0.8 bu/ft³ (or 1 ÷ 1.2445 legal). Full-peak height = r × tan(filling angle). Optional packing adds a percentage. Tests reproduce Nebraska CropWatch's 30 ft × 17 ft = 9,608 bu plus a 6 ft peak = 1,128 bu.

Test weight and dockage

Standard bushels = volume bushels × test weight ÷ standard weight. Grade limits from 7 CFR 810.404 (corn) and 810.2204 (wheat); test weight isn't a soybean grade factor under 810.1604. Scale tickets: dockage deducted from gross, then moisture shrink, then a price discount per pound of test weight below the threshold you enter.

Crop constants

Croplb/buBase moistureFilling angle
Corn (shelled)5615.5%23°
Soybeans6013%25°
Wheat6013.5%25°
Grain sorghum (milo)5614%25°*
Barley4814.5%28°
Oats3214%28°
Canola5010%25°*
Sunflower (oil)cwt10%30°*
Angles from NDSU AE-84 for corn, soybeans, wheat, barley and oats; * approximate. Base moisture is a common buyer base and is editable everywhere.

Sources

  1. Iowa State University Extension, Ag Decision Maker A2-32: Grain Drying and Shrink (Edwards)
  2. Iowa State University Extension, Ag Decision Maker A2-31: Estimating the Cost of Drying Corn
  3. Iowa State University Extension, Ag Decision Maker C6-82: Storage Capacity for Grains, Forages and Liquids
  4. Purdue Extension NCH-61: Calculating Grain Weight Shrinkage in Corn Due to Mechanical Drying (Hicks & Cloud)
  5. University of Minnesota Extension: Energy costs for corn drying and cooling
  6. University of Minnesota Extension: Natural-air corn drying
  7. NDSU Extension (Hellevang): Crop Drying Tips for a Wet Year
  8. NDSU Extension: guidance for corn harvest and drying (2023)
  9. NDSU Extension AE-84: Temporary Grain Storage (filling angles, pile capacity)
  10. University of Nebraska–Lincoln CropWatch: How to Estimate Bushels of Grain in a Bin
  11. Bhadra et al., Pack Factor Measurements for Corn in Grain Storage Bins, Trans. ASABE 58(3), 2015
  12. USDA FGIS, U.S. Standards for Corn (7 CFR 810.401–810.405)
  13. USDA FGIS, U.S. Standards for Soybeans (7 CFR 810.1601–810.1605)
  14. USDA FGIS, U.S. Standards for Wheat (7 CFR 810.2201–810.2205)